Components and Subsystems

CTP-4408 Series Medium Current Inductor

CTP-4408 is a medium current inductor with Core type: 0.80” o.d., Iron Powder, perm 75.
Power rating: 1.2 watts for temp. rise 50 deg C.Typical applications: Input and output filters in Switch Mode Power Supplies.

Features: 
  • Flying leads (1.00”), for vertical or horizontal mounting
  • 4-pin header, for vertical mounting
  • Threaded center hole, flying leads
  • 2-pin header, for vertical mounting

CTP-4407 Series Medium Current Inductor

CTP-4407 is a medium current inductor with Core type: 0.68” o.d., Iron Powder, perm 75.
Power rating: 0.86 watts for temp. rise 50 deg C. Typical applications: Input and output filters in Switch Mode Power Supplies.

Features: 
  • Flying leads (1.00”), for vertical or horizontal mounting
  • 4-pin header, for vertical mounting
  • Threaded center hole, flying leads
  • 2-pin header, for vertical mounting

CTP-4406 Series Medium Current Inductor

CTP-4406 is a medium current inductor with Core type: 0.50” o.d., Iron Powder, perm 75.
 Power rating: 0.50 watts for temp. rise 50 deg C. Typical applications: Input and output filters in Switch Mode Power Supplies.

Features: 
  • Flying leads (1.00”), for vertical or horizontal mounting
  • 4-pin header, for vertical mounting
  • Threaded center hole, flying leads
  • 2-pin header, for vertical mounting

TEW-4229 Series Input/Output Transformer

TEW 4229 is a DNIC interface Transformer approved by Mitel for use with their MT8972 and MT8971B/72B devices.

Features: 
  • Digital subscriber lines
  • High speed data transmission over twisted wire
  • Digital PABX line cards and telephone sets

TLA-4215 Series 2-Coil Hybrid Transformer

TLA-4215 is designed to be used in a 2-coil hybrid transformer configuration. Interfacing of Telecommunications equipment requiring separate transmit and receive path to a 2-wire telephone line, where high transhybid loss and DC loop current capability are required.

Features: 
  • Low profile
  • Small size
  • DC capability
  • Conforms to FCC Part 68 and C03 regulations

TEA-4214 Series Matching Transformer

TEA-4214 is a wide band matching transformer operating in two impedance configurations. The 4214 is mainly used as Line Matching and Bridging Transformer.  Windings connected in parallel for lower impedances ( 100 to 150 Ω) and connected in series for higher impedances ( 600 to 900 Ω).

Features: 
  • Very wide band
  • Low insertion loss
  • Low bridging loss

4175-4177 Series Bandpass Filters

Bandpass Filters designed for high frequency communications equipment where high
stability over a wide temperature range is mandatory.

 .

Features: 
  • ± 4° phase match between filters
  • Small size
  • Low cost

TEW-4087 Series Matching Transformer

The TEW-4087 transformer was designed to provide matching between a coax cable and a twisted pair.

Features: 
  • Based on the Ethernet data link protocol
  • Uses baseband signaling at 10Mbps

TLA-4032 Series Matching Line Transformer

TLA-4032 is a 1 : 1 line matching transformer. Line matching in 600 & 900 Ω circuits where DC loop current capability and high voltage insulation are required.

Features: 
  • Low profile
  • DC loop current capability
  • Conforms to FCC part 68, Canadian CS 03, British BS 6305 and Australian regulations
  • High voltage insulation between input and output windings

3858-X Series Line Coupling/Bridge Transfomer

3858 is a 1:1 line matching transformer. Interfacing equipment to telephone line, requiring small size and high insulation voltage.
3858-2 is designed for high impedance bridging applications.

Features: 
  • Low profile
  • Small volume
  • Conforming to FCC part 68, Canadian CS 03 regulations
  • Low cost
  • High insulation voltage
Syndicate content